Компактные экскаваторы / Компактный экскаватор E27z
Спецификации и опции
E27z
Закрыть/открыть все PDF version
Operating weight with cab and bucket (ISO 6016)
2,705 kg
Transport mass (no attachment)
2,571 kg
Weight reduction with canopy
-118 kg
Additional weight for steel tracks
130 kg
Additional weight for long dipperstick
14 kg
Additional weight for heavy counterweight
91 kg
Ground pressure with rubber tracks
25 kPa
(A)
Bucket pivot angle
185 °
(B)
Maximum reach of working equipment
4,644 mm
(B*)
Maximum reach of working equipment, long dipperstick
4,931 mm
(C)
Maximum reach at ground level
4,518 mm
(C*)
Maximum reach at ground level, long dipperstick
4,814 mm
(D)
Maximum working equipment radius with boom at maximum height and dipperstick fully retracted
2,131 mm
(D*)
Maximum working equipment radius with boom at maximum height and dipperstick fully retracted, long dipperstick
2,135 mm
(E)
Maximum blade height
385 mm
(F)
Maximum blade depth
420 mm
(G)
Maximum height of working equipment with dipperstick retracted
3,247 mm
(H)
Maximum bucket tooth height
4,230 mm
(H*)
Maximum bucket tooth height, long dipperstick
4,430 mm
(I)
Maximum dump height
3,043 mm
(I*)
Maximum dump height, long dipperstick
3,243 mm
(J)
Maximum depth of vertical wall which can be excavated
1,567 mm
(J*)
Maximum depth of vertical wall which can be excavated, long dipperstick
1,818 mm
(K)
Maximum digging depth
2,547 mm
(K*)
Maximum digging depth, long dipperstick
2,847 mm
()
(* Dentoes values which long dipperstick installed)
(A)
Blade height
319 mm
(B)
Clearance, upper structure to ground line
539 mm
(C)
Ground line to top of engine cover
1,540 mm
(D)
Length of track on ground
1,543 mm
(E)
Machine centre line to blade
1,462 mm
(F)
Minimum radius in travel position
3,343 mm
(G)
Overall length of track assembly
1,965 mm
(H)
Overall length in travel position
4,325 mm
(I)
Track lug height
21 mm
(J)
Blade width
1,550 mm
(K)
Height
2,438 mm
(L)
Track width
300 mm
(M)
Machine centre line to working equipment centre line, left-hand rotation
565 mm
(N)
Machine centre line to working equipment centre line, right-hand rotation
773 mm
(O)
Minimum turning radius
1,726 mm
(P)
Swing clearance, rear
785 mm
(Q)
Working width at maximum right-hand rotation
1,808 mm
(R)
Working width at maximum left-hand rotation
1,599 mm
Make / model
Yanmar / 3TNV76-PBC (Stage V)
Fuel
Diesel
Number of cylinders
3
Displacement
1,116 cm3
Maximum power @ 2400 rpm (ISO 14396)
14.9 kW
Maximum torque @ 1800 rpm (SAE J1995)
66.3 Nm
Pump type
Dual outlet variable displacement piston pump with gear pumps
Total hydraulic capacity
94.2 L/min
Piston pump capacity
67.5 L/min
Auxiliary (AUX1) flow
53.8 L/min
Auxiliary (AUX2) flow
20 L/min
Auxiliary (AUX1) relief
180 bar
Auxiliary (AUX2) relief
179 bar
Digging force, dipperstick (ISO 6015)
16,200 N
Digging force, long dipperstick (ISO 6015)
13,470 N
Digging force, bucket (ISO 6015)
23,720 N
Drawbar pull
29,023 N
Travel speed, low range
2.5 km/h
Travel speed, high range
4.3 km/h
Boom swing, left
70 °
Boom swing, right
55 °
Slew rate
9.3 RPM
Fuel reservoir
34.4 L
Hydraulic reservoir
10.2 L
Noise level LpA(EU Directive 2006/42/EC)
79 dB(A)
Noise level LWA(EU Directive 2000/14/EC)
93 dB(A)
Whole body vibration (ISO 2631–1)
0.2 ms-2
Hand-arm vibration (ISO 5349–1)
0.5 ms-2
- 1550 mm dozer blade
- 300 mm rubber tracks
- Adjustable double acting auxiliary hydraulic (AUX1) with Quick Couplers
- Battery disconnect switch
- Blade float feature
- Clamp ready
- Control console locks
- Cupholder
- Dual Direction Detent
- Engine/hydraulic monitor with shutdown
- Foldable and ergonomic travel pedals
- Full fuel warning alarm
- Horn
- Proportional fingertip auxiliary and boom swing offset hydraulic control
- Retractable seat belt
- Suspension seat with high back
- Storage compartment
- TOPS/ROPS/FOPS canopy * (1)
- Two-speed travel with Auto shift
- Upper structure four-point tie down
- Work light (boom)
- Water separator
- Warranty: 24 months, 2000 hours (whichever occurs first)
(1) Roll Over Protective Structure (ROPS) – Meets requirements of ISO 3471. Tip Over Protective Structure (TOPS) – Meets requirements of ISO 12117. Falling Object Protective Structure (FOPS) - Meets requirements of ISO 3449.
- Additional halogen lights
- AM/FM/DAB radio + phone call ready
- A-SAC package (Tilt coupler lines, Dlx displ.)
- Auto idle
- AUX1 direct return to tank
- AUX1/AUX2/Drain on arm
- AUX2 hydraulics
- Beacon
- Bobcat hydr. pin grabber
- Bucket valves (AUX3) kit
- Case drain line kit
- Clamp w/ AUX1 valve
- Comfort package cab (Cloth susp. seat & Dlx displ.)
- Comfort package plus cab (Heated seat, Dlx displ.)
- Demolition package (arm & bucket cylinder covers) kit
- Grease Gun Set (Gun + Holder in Machine)
- Heavy counterweight
- Hydr. coupler lines (AUX5)
- Keyless ignition
- L/R mirrors
- LED lights set
- Long dipperstick
- Object handling package (Valves, OWD, Lifteye)
- Special application kit
- Steel tracks
- TOPS/ROPS/FOPS cab
- Travel motion alarm
Некоторые данные основаны на инженерных расчетах, а не на результатах измерений. Данные приведены только для целей сравнения и могут быть изменены без предварительного уведомления. Технические данные вашей машины Bobcat могут варьироваться в соответствии с обычными изменениями, которые могут быть внесены в конструкцию или технологию изготовления, а также в соответствии с условиями работы и другими факторами.