E27 Compact Excavator
Specifications & Options
E27
Close/Open all PDF version
Operating weight with cab and bucket (ISO 6016)
2,683 kg
Transport mass (no attachment)
2,549 kg
Weight reduction with canopy
-118 kg
Additional weight for steel tracks
130 kg
Additional weight for heavy counterweight:
147 kg
Ground pressure with rubber tracks
26.2 kPa
(A)
Bucket pivot angle
185 °
(B)
Maximum reach of working equipment
4,721 mm
(C)
Maximum reach at ground level
4,604 mm
(D)
Maximum working equipment radius with boom at maximum height and dipperstick fully retracted
1,924 mm
(E)
Maximum blade height
346 mm
(E*)
Maximum blade height with long blade
385 mm
(F)
Maximum blade depth
302 mm
(F*)
Maximum blade depth with long blade
420 mm
(G)
Maximum height of working equipment with dipperstick retracted
3,240 mm
(H)
Maximum bucket tooth height
4,429 mm
(I)
Maximum dump height
3,243 mm
(J)
Maximum depth of vertical wall which can be excavated
1,825 mm
(K)
Maximum digging depth
2,847 mm
()
(* Dentoes values which long dipperstick installed)
(A)
Blade height
319 mm
(B)
Clearance, upper structure to ground line
539 mm
(C)
Ground line to top of engine cover
1,540 mm
(D)
Length of track on ground
1,543 mm
(E)
Machine centre line to blade
1,245 mm
(E*)
Ground clearance
1,462 mm
(F)
Minimum radius in travel position
3,135 mm
(G)
Overall length of track assembly
1,965 mm
(H)
Overall length in travel position
4,079 mm
(H**)
Overall length in travel position with Heavy counterweight
4,190 mm
(I)
Track lug height
21 mm
(J)
Blade width
1,550 mm
(K)
Height
2,438 mm
(L)
Track width
300 mm
(M)
Machine centre line to working equipment centre line, left-hand rotation
393 mm
(N)
Machine centre line to working equipment centre line, right-hand rotation
576 mm
(O)
Minimum turning radius
1,575 mm
(P)
Swing clearance, rear
995 mm
(P**)
Swing clearance, rear with heavy counterweight
1,055 mm
(Q)
Working width at maximum right-hand rotation
1,808 mm
(R)
Working width at maximum left-hand rotation
1,731 mm
(R**)
Working width at maximum left-hand rotation with heavy counterweight
1,791 mm
Make / model
Kubota / D1305-E4B-BCZ-1 (Stage V)
Fuel
Diesel
Number of cylinders
3
Displacement
1,261 cm3
Maximum power @ 2400 rpm (ISO 14396)
18.3 kW
Maximum torque (SAE)
81.3 Nm
Pump type
Dual outlet variable displacement piston pump with gear pumps
Total hydraulic capacity
94.3 L/min
Auxiliary (AUX1) flow
54 L/min
Auxiliary (AUX2) flow
20 L/min
Auxiliary (AUX1) relief
180 bar
Auxiliary (AUX2) relief
179 bar
Digging force, dipperstick (ISO 6015)
16,030 N
Digging force, bucket (ISO 6015)
26,520 N
Drawbar pull
28,949 N
Travel speed, low range
3 km/h
Travel speed, high range
5.1 km/h
Boom swing, left
70 °
Boom swing, right
55 °
Slew rate
9.3 RPM
Fuel reservoir
34.4 L
Hydraulic reservoir
10.2 L
Noise level LpA(EU Directive 2006/42/EC)
78 dB(A)
Noise level LWA(EU Directive 2000/14/EC)
93 dB(A)
Whole body vibration (ISO 2631–1)
0.1 ms-2
Hand-arm vibration (ISO 5349–1)
0.4 ms-2
- 1550 mm dozer blade
- 300 mm rubber tracks
- Adjustable double acting auxiliary hydraulic (AUX1) with Quick Couplers
- Battery disconnect switch
- Blade float feature
- Clamp ready
- Control console locks
- Cupholder
- Dual Direction Detent
- Engine/hydraulic monitor with shutdown
- Foldable and ergonomic travel pedals
- Full fuel warning alarm
- Horn
- Proportional fingertip auxiliary and boom swing offset hydraulic control
- Retractable seat belt
- Suspension seat with high back
- Storage compartment
- TOPS/ROPS/FOPS canopy * (1)
- Two-speed travel with Auto shift
- Upper structure four-point tie down
- Water separator
- Work light (boom)
- Warranty: 24 months, 2000 hours (whichever occurs first)
(1) Roll Over Protective Structure (ROPS) – Meets requirements of ISO 3471. Tip Over Protective Structure (TOPS) – Meets requirements of ISO 12117. Falling Object Protective Structure (FOPS) - Meets requirements of ISO 3449.
- Comfort package cab (Cloth susp. seat & Dlx displ.)
- A-SAC package (Tilt coupler lines, Dlx displ.)
- Object handling package (Valves, OWD, Lifteye)
- TOPS/ROPS/FOPS cab
- Heavy counterweight
- Steel tracks
- AUX1 direct return to tank
- AUX2 hydraulics
- AUX1/AUX2/Drain on arm
- Bucket valves (AUX3) kit
- Hydr. coupler lines (AUX5)
- Case drain line
- Auto idle
- Keyless ignition
- Travel motion alarm
- AM/FM MP3 radio
- Additional halogen lights
- LED lights set
- Beacon
- Special application kit
- L/R mirrors
- Clamp w/ AUX1 valve
- Klac D and MS03 coupler
- Bobcat hydr. pin grabber
- Grease gun w/ holder
Certain specification(s) are based on engineering calculations and are not actual measurements. Specification(s) are provided for comparison purposes only and are subject to change without notice. Specification(s) for your individual Bobcat equipment will vary based on normal variations in design, manufacturing, operating conditions, and other factors.